Nissan 240SX Forums banner
Cancel
Create thread New Garage Forums

Quality RUCAs, Toe Conrtol Arms

Jump to Latest
1 - 14 of 14 Posts
B

byhi

· Registered
Joined
·
267 Posts
Discussion starter · #1 ·
So i need some beefy RUCAs. Alot of stress is put on these things and i'm going to be correcting my camber to as close to 0 degrees as possible. I am also running 18 x 13's on them so even more stress is being put on them. I also need rear toe control arms to go with them b/c it's less stress on the RUCAs and it obvioulsy helps me adjust back there better. My question is are there any companies that have like a magical warrenty b/c they believe in their product so much that if i bend them i can get a new one? Probably not bet eh. So the other question is are there any super beefy ones that will never break on me? Like what do people run that have 10 + in the rear and drift super hard on them? And i need TC rods, i don't think those break too often as long as they are a good brand, but mabye they do. Please enlighten me. Thanks
 
#3 ·
why would you set your camber to 0? toe, i can understand, but a very slight negative camber like a degree or two, isn't going to kill your tires.

SPL
Kazama
Cusco (same as SPL for s14)
Battle Version

that's all i can think of.
 
Save
Reply Quote Like Like
Discussion starter · #5 ·
i suppose that a few degress aren't bad, but i really dont wan to go through tires too fast. I won't be doing much drifting on these rims because tires cost way too f-in much. Since i'm running 305's, i can't find used ones very easily or for very cheap. Thanks for the suggestions. I'll be buyin some super soon. Also anyone ever bent of these even under hard driving first hand?
 
#6 ·
i haven't. i had c-tune ruca's. they're on ebay too. the welds weren't exactly clean, but they were strong. and i never had problems with the spherical bearings.
however, the design quality of Cusco/SPL's is very very nice.
 
Save
Reply Quote Like Like
Discussion starter · #8 ·
i don't really know alot about peak performance. Can you tell me their story. I feel like a noob but eh, whatever.
And ine off ebay looked great when i got them. The welds on them looked good and everything. But the metal was thinner than it felt like and bent in half. What a pair of H-MO's.
 
Discussion starter · #11 ·
angelthepig, true that on the toe kills your tires. I also have a welded diff so it puts more where on the tires everytime i go around a tight corner normally. Well i think ill prolly get battle version or spl. I posted in the for sale section al ready, but anybody got some for sale? S14?
 
#12 ·
I got all my Battle Version stuff from Superior Nissan of Puente Hills. Crazy place, its a Nissan dealership but they carry nismo, tein, sparco, and tons of other aftermarket brands. They had an 800hp blitz R34 GTR in the showroom when i went. I was just like "oh there's the new altima SE-R and WTF?!" lol, its a little pricey but i compared it to the actual battle version site and prices were about the same. If you're forced to buy new pieces check out http://www.superiornissanmotorsports.com
 
1 - 14 of 14 Posts
About this Discussion
13 Replies
7 Participants
Last post:
raen419
Nissan 240SX Forums
posts
1.6M
members
94K
Since
2002
A forum community dedicated to Nissan 240SX owners and enthusiasts. Come join the discussion about performance, builds, engine swaps, turbos, modifications, classifieds, troubleshooting, maintenance, and more!
Full Forum Listing
Explore Our Forums
S13 240SX (89-94) New Member Introductions General Tech S14 240SX (95-98) KA24DE & KA24E