Nissan 240SX Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 83 Results
  1. S13 240SX (89-94)
    Hey yall I need help finding the part number for this particular hose. It goes on the intake plenum (KA24E SOHC). Any help would be appreciated. Here’s the pictures:
  2. S13 240SX (89-94)
    Pictures: This little connector was corroded so badly that it tore right off the wiring harness like a thin twig. I’m not sure what it goes to, I think it was plugging into some EGR component - it was in the midsection under the cowl behind the valve cover (KA24E SOHC). Anyway, I was...
  3. KA24DE & KA24E
    I busted my clutch fan + fan shroud assembly. The OEM KA fan shroud (21476-40F00 - Shroud. (Upper) - Genuine Nissan Part) is about $50 more than the OEM SR fan shroud (https://www.enjukuracing.com/products/oem-fan-shroud-nissan-240sx-sr20.html). Will the SR fan shroud fit in my engine bay...
  4. New Member Introductions
    So I've owned a 240 for about 3 or 4 years now and the body isn't going to last much longer I do all my own work and never go to shops bit I still need some help, I recently bought a 94 hard body xe trim level and I'm pretty sure the engine is shot. I'm curious about doing a swap bit can't seem...
  5. New Member Introductions
    I just swapped a ka24e from a hardbody, into my 89 240 it's getting fuel just no power to the ignitor . I did everything correct swapped the intake, oil pan , and starter. I've probably read about 100 forums i've tried almost everything, it cranks it just doesn't turn over. I've taken off...
  6. Blog
    I have gone thru 3 ecus with my 240 in the past month. the first one was due to a wiring issues wich i fixed and the car ran fine. the second one was due to bugs getting into it and completely messing the board up. the third one is actually quite the mystery. so on saturday i drove the car all...
  7. S13 240SX (89-94)
    Hey guys, so I keep getting a misfire at around 4k rpms Also when checking the timing to adjust the the degrees on the distributor the notches on the crank do not spin steady it seems to be bouncing slightly between degrees... anyone have a similar issue or have any suggestions?
  8. KA24DE & KA24E
    Hey guys, so I'm having hesitation issues with my single cam and I am pretty sure its due to the tps sensor because the hesitation only occurs between 1500 to 3500 rpms. I'm going to be getting a replacement for it but I was a bit curious. Is there an compatible throttle or sensor from another...
  9. New Member Introductions
    Hey guys, I have a 1990 240sx. Ka24e.. I am having issues with my speedometer, it will work sometimes and sometimes it won't. When it is not working it will either sit at 0 or bounce around randomly. Not sure what could be causing this.
  10. KA24DE & KA24E
    ok so i just rebuilt my ka and i had to get a new starter but it doesn't fit the cone is too long and is hitting the back of the bell housing. So i put shims in it well washers and it just grinds. So if i take one washer off it locks in to the flywheel and doesnt move at all. I tried to roll...
  11. New Member Introductions
    I have a s13 that is currently leaking coolant. I have already replaced the waterpump and it seems like it's not leaking from there. What I did found was that the cap next to the intake pipe that is marked with a "L" is leaking. Is this the source of my leak? where can I buy parts to fix it...
  12. New Member Introductions
    Hey, first time posting, but let me get straight to the point. I bought this 90' ka24e 240sx several weeks back, and have been trouble shooting it and making it reliable, but I found some very odd electical problems under the steering colom. Previous owner had a amp and sub horribly wired up as...
  13. KA24DE & KA24E
    this is what my motor sounds like at the moment. i got the car said it had a blown head gasket ,240sx hatch 89 se i took apart the engine and the head gasket had holes in it , so i replaced it and replaced all the easy gakets that i took off the get to the head. when i put the motor back to...
  14. New Member Introductions
    I just bought my first 240sx and its timing chain was rattling at start so i went to replace it. Took me 2 days to get the cover off now thats it off i put on a new chain but the chain seems to be either to long bcuz its loose or i put the chain on wrong causing it to be loose. I bought a new...
  15. KA24DE & KA24E
    First off, this is not a bash tread. I am mainly stating my opinion and experience toward the product and service I received from O&J Performance. It's probably going to be quite long, so I'll post cliffs at the bottom. On August 15th of 2012, I purchased a camshaft as a gift for my brothers...
  16. KA24DE & KA24E
    I'm working on a dual cam ka swap in my 90' s13 and I don't want to buy a new exhaust if I don't have to, Thanks!
  17. New Member Introductions
    Hey guys, I've never made a forum post, I tend to be more of a researcher than a question asker but I have plenty of questions and figured I'd ask some experienced ka builders in here. I'm looking for approx. 250-300hp preferably 300hp, and I think for the most part I have all the basic build...
  18. New Member Introductions
    Hey guys! I am here today because I traded my beloved MK3 Supra for a S13 (plus i got a few bux :} ) Basically I had my soup for 5 years and I am a grad student so I had to get rid of it, it had MANY random issues and I was tired of working on the 7MGTE honestly... Didn't feel like swapping...
  19. Items for Sale
    I'm currently selling my s13 ka24e complete engine and S14 ka24de incomplete engine. The Sohc had blown the head gasket and head will need to be sent to a machine shop to be recovered, but is a complete engine. The Dohc is in fair condition, but needs new pistons from boost damage, and a...
1-20 of 83 Results
Top